UK Automation
Call us on 0845 094 0089
  Top » Catalogue » X10 Home Automation » X10 Inline Modules » AW12 Welcome to UK Automation - Would you like to log in?
30 Day Money Back Guarantee on all purchases

Marmitek X10 Appliance Module AW12 (Micro Module)
[AW12]

 33.56 
(£28.56 ex. VAT)

Features

Availability:
In stock ready to dispatch
Like this item? Share it!

Bookmark and Share
  • This Marmitek MicroModule can be installed behind conventional wall switches or into wall outlets because of the extreme small size of the MicroModule (H = 4.6cm x W = 4.6 cm x D = 1.7cm, Minimum built-in depth 40 mm, advised 50 mm). The MicroModule is also ideal for installation into light fixtures or for use in areas with limited space such as rooms with lowered ceilings.
  • Universal compatibility: No limitation in choosing brand, color or type of any wall switches and outlets.

This module can be controlled by normal switches or momentary switches connected to the module or remotely using the Marmitek X10 (PLC) signal via the mains. The module responds to the following Marmitek X10 PLC commands: On, Off and the optional Marmitek X10 commands All Lights On/All Lights Off/All Units Off when these have been programmed. Both normal switches (make/break) and momentary switches can be connected to the module. The input from the switch is connected to the live (brown wire, 230 V), the output from the switch is connected to the thin black wire (input) on the AW12 module. This is illustrated in figure A. The AW12 can also be used in a 2 way switching circuit, see Diagram B in 'How to install'.

When power is lost the module will retain the state it was in before the loss. (on/off) The AW12 uses 1-way X10 communications.

pdf Click here for Data Sheet

NB requires a neutral connection.

For further information about Marmitek Micro Modules click on Marmitek comparison table


How to install

Availability:
In stock ready to dispatch
Like this item? Share it!

Bookmark and Share

To install the Marmitek AW12, neutral and phase are required at the installation point.

  • Switch off appropriate mains fuse and master switch!
  • Take the wall switch out of the wall box.
  • Disconnect all wires from the switch.
  • Pull an additional Neutral wire if it is missing.
  • Connect the live and neutral to the terminal wires of the AW12 as described in figure A.
  • Connect the wire from the In-Wall module to the switch.
  • Connect the live to the switch.
  • Replace the wall switch.
  • Switch on mains fuse and master switch.

Marmitek AW12 instruction diagram

Marmitek AW12 instruction diagram


Specification

Availability:
In stock ready to dispatch
Like this item? Share it!

Bookmark and Share
  • Supply voltage: 230V - 50 Hz
  • Supply current : < 20 mA capacitive
  • Switching power: 3600 W/230V for resistive (ohm) load
    600 W/230V for inductive/capacitive load
    2000 W/230V for light bulbs and low voltage halogen lights with transformer.
  • Minimum load: 3W
  • Signal sensitivity: 15 mVpp min 50 mVpp max at 120 kHz
  • Input impedance: > 180 Ohm (L - N) at 120 kHz
  • Connections: Wire for a standard pressure switch or momentary switch and connecting clamps for phase, neutral and switched phase.
  • Ambient temperature: - 10 C to + 40 C (operation) - 20 C to + 70 C (storage)
  • Dimensions: 46x46x17mm

Reviews

Darren Williams - 30/03/2010 

Clear installation instructions and easy to wire into the existing system. I was using the default house codes so didn't need to alter anything. When I purchased this, I understood that it would work directly with a wireless switch unit, but that was my mistake. This requires at least one transceiver unit to be present on the system to effect the switching. Having said that it allows the switching of the appliance via the wired switch or the X10 system. This is being used to switch a ceiling light with a D-ring flourescent and it works. Thanks for the tip from UKAutomation on it's suitability. I had prompt and clear advice from them and would definitely purchase from here again.

Jim Deakin - 01/04/2009 

The device is compact and easy to fit, but assigning device codes is not like a standard fitting. It needs to be electronically switched to a program mode and codes sent to it. I've not got around to doing this yet, as the default ID is ok and I have no other similar devices, so there's no clash. It would be useful if this was made clear on the install info screen, and they could give some tips on how to do it too.

Click to view All Reviews

Customer reviews

  • Darren Williams - Submitted on: 30/03/2010

    Clear installation instructions and easy to wire into the existing system. I was using the default house codes so didn't need to alter anything. When I purchased this, I understood that it would work directly with a wireless switch unit, but that was my mistake. This requires at least one transceiver unit to be present on the system to effect the switching. Having said that it allows the switching of the appliance via the wired switch or the X10 system. This is being used to switch a ceiling light with a D-ring flourescent and it works. Thanks for the tip from UKAutomation on it's suitability. I had prompt and clear advice from them and would definitely purchase from here again.

  • Jim Deakin - Submitted on: 01/04/2009

    The device is compact and easy to fit, but assigning device codes is not like a standard fitting. It needs to be electronically switched to a program mode and codes sent to it. I've not got around to doing this yet, as the default ID is ok and I have no other similar devices, so there's no clash. It would be useful if this was made clear on the install info screen, and they could give some tips on how to do it too.

Click to view All Reviews

If you have any questions about this product, you can either:
Post a message on the forum
Or click here to email us about this product
Price:  33.56  inc. VAT
Availability:  In stock ready to dispatch
Quantity: 
Reviews

Bye Bye Standby Remote Control Lamp Dimmer Socket

Bye Bye Standby Keyfob Remote Control

GlowFlow - Temperature controlled basin light

Marmitek Infrared extenders: Control Anywhere

X10 Double Light Switch

Marmitek Comfort Remote Control for X10 Security Systems

My Basket
0 items
My Account
Log In
Manufacturer
Other products

Follow us on Twitter for the latest news and special 'Twitter Only' offers!




Card payments via SagePay  PayPal  Visa Mastercard Delta Maestro Solo Electron Verified by Visa Mastercard Secure