Loading... Please wait...

Our Newsletter

Reviews of uk-automation.co.uk

Marmitek X10 Appliance Module & Transmitter AWM2P (Micro Module)

  • Marmitek X10 Appliance Module & Transmitter AWM2P (Micro Module)
Calculated at checkout
Bookmark and Share

Product Description


  • X10 transmitter for two sequential X10 addresses (ON/OFF).
  • Built-in 16A appliance module.
  • Two-way X10 communications.
  • Two wall switches can be connected with one MicroModule. One serves the internal appliance module and also gives the X10 commands through the power line. The second wall switch is used to transmit a second X10 address (ON/OFF).
  • X10 programmable (See below)
  • Responds to or ignores All-Lights-On and All-Units-Off commands.
  • Built-in appliance module remembers its last known state between power failures or disconnections.

A manual for this product is available:

pdf Click here to read the AWM2P manual - 350Kb

For further information about Marmitek Micro Modules click on Marmitek comparison table

How to Install

To Install the AWM2 MicroModule, the following wiring are required at the installation point: Live, Neutral and Load.

  • Take the wall switch out of the wall outlet.
  • Disconnect all wires from the switch.
  • Pull an additional Neutral wire if it is unavailable.
  • Connect the Live, neutral and load wires to the terminals on the MicroModule.
  • Connect the control wires to the existing wall switch(es) with the blue wire as the common.
  • Position the MicroModule against the back wall of the wall outlet behind all the wires.
  • The MicroModule is now ready for configuration.
  • Refit the wall switches at its original position after the MicroModule has been programmed.


Dimensions: Length 47, Width 18, Height 47 mm
Supply voltage: 230V +10%/-15% 50Hz
Supply current: =< 30mA capacitive
Making capacity: 2KW (incandescent lamp)
3A (motors)
16A (resistive loads)
Signal transmission: > 5Vpp in 5Ohm at 120KHz +- 1KHz
according to EN50065-1, EN50065-2-1, EN50065-4-1
X-10 transmission: 1 pulse burst at zero and 180 degrees
Signal sensitivity: 25mVpp .. 6Vpp at 120KHz +- 4KHz
S to N ratio: 1.35:1
Connections: Up to 2.5mm square
Ambient temperature: -10ºC to +40ºC (operation), -20ºC to +70ºC (storage)
Approvals: NEN-EN-IEC 60669-2-1 and NEN-EN-IEC-60669-2-2
This product is CE approved for use in the EU


  • Installs behind conventional wall switches or into wall outlets because of the extremely small size of the module (minimum built-in depth 40mm, advised 50mm). The MicroModule is also suitable for installation into light fixtures, home appliances or for use in areas with limited space such as lowered ceilings.
  • Universal compatibility. No limitation in choosing brand, colour or type of any wall switches and outlets.
  • Can be used in combination with regular or momentary switches. These will be automatically recognised by the module.
  • Install two-way switches without adding additional wires in between wall switches (the MicroModule transmits their status to other modules through the power line when manually switched).
  • Execute macros and preferred scenarios with a conventional switch.


Find Similar Products by Category

Write your own product review

Product Reviews

This product hasn't received any reviews yet. Be the first to review this product!

Why buy from us?

Great customer service

Telephone support during office hours, and email support quite often out of hours too!

30 day money back guarantee

All products are covered by our 30 day money back guarantee. If you're not happy, return the goods to us in the condition you received them for a full refund.

Free 'super saver' delivery

Not in a hurry? Our super saver delivery option gives you free delivery within 5 - 7 days (although many customers receive their items much quicker!)

Add to Wish List

Click the button below to add the Marmitek X10 Appliance Module & Transmitter AWM2P (Micro Module) to your wish list.

You Recently Viewed...