UK Automation
Call us on 0845 094 0089
  Top » Catalogue » X10 Home Automation » X10 Inline Modules » AWM2P Welcome to UK Automation - Would you like to log in?
Free shipping on all orders over 200
30 Day Money Back Guarantee on all purchases

Marmitek X10 Appliance Module & Transmitter AWM2P (Micro Module)

(£58.67 ex. VAT)


In stock ready to dispatch
  • X10 transmitter for two sequential X10 addresses (ON/OFF).
  • Built-in 16A appliance module.
  • Two-way X10 communications.
  • Two wall switches can be connected with one MicroModule. One serves the internal appliance module and also gives the X10 commands through the power line. The second wall switch is used to transmit a second X10 address (ON/OFF).
  • X10 programmable (See below)
  • Responds to or ignores All-Lights-On and All-Units-Off commands.
  • Built-in appliance module remembers its last known state between power failures or disconnections.

A manual for this product is available:

pdf Click here to read the AWM2P manual - 350Kb

For further information about Marmitek Micro Modules click on Marmitek comparison table

How to Install

In stock ready to dispatch

To Install the AWM2 MicroModule, the following wiring are required at the installation point: Live, Neutral and Load.

  • Take the wall switch out of the wall outlet.
  • Disconnect all wires from the switch.
  • Pull an additional Neutral wire if it is unavailable.
  • Connect the Live, neutral and load wires to the terminals on the MicroModule.
  • Connect the control wires to the existing wall switch(es) with the blue wire as the common.
  • Position the MicroModule against the back wall of the wall outlet behind all the wires.
  • The MicroModule is now ready for configuration.
  • Refit the wall switches at its original position after the MicroModule has been programmed.


In stock ready to dispatch

Dimensions: Length 47, Width 18, Height 47 mm
Supply voltage: 230V +10%/-15% 50Hz
Supply current: =< 30mA capacitive
Making capacity: 2KW (incandescent lamp)
3A (motors)
16A (resistive loads)
Signal transmission: > 5Vpp in 5Ohm at 120KHz +- 1KHz
according to EN50065-1, EN50065-2-1, EN50065-4-1
X-10 transmission: 1 pulse burst at zero and 180 degrees
Signal sensitivity: 25mVpp .. 6Vpp at 120KHz +- 4KHz
S to N ratio: 1.35:1
Connections: Up to 2.5mm square
Ambient temperature: -10C to +40C (operation), -20C to +70C (storage)
Approvals: NEN-EN-IEC 60669-2-1 and NEN-EN-IEC-60669-2-2
This product is CE approved for use in the EU


In stock ready to dispatch
  • Installs behind conventional wall switches or into wall outlets because of the extremely small size of the module (minimum built-in depth 40mm, advised 50mm). The MicroModule is also suitable for installation into light fixtures, home appliances or for use in areas with limited space such as lowered ceilings.
  • Universal compatibility. No limitation in choosing brand, colour or type of any wall switches and outlets.
  • Can be used in combination with regular or momentary switches. These will be automatically recognised by the module.
  • Install two-way switches without adding additional wires in between wall switches (the MicroModule transmits their status to other modules through the power line when manually switched).
  • Execute macros and preferred scenarios with a conventional switch.


There are currently no reviews for this product.
Why not be the first to write one?

If you have any questions about this product, please click here
Price:  67.47  inc. VAT
Availability:  In stock ready to dispatch

Marmitek X10 Appliance Module AM12W (wired)

X10 MC10 Mini Controller

X10 Computer Interface

X10 Handheld RF Remote Control

Marmitek EasyControl 8 Remote Control

Marmitek X10 Shutter/Sunblind switch SWM1P (Micro Module)
My Basket
0 items
My Account
Log In
Other products
Live Support

Secure Site
UK Automation is fully secured by GeoTrust QuickSSL
Card payments via SagePay Visa Mastercard Delta Maestro Solo Electron Verified by Visa Mastercard Secure